The Art of Basic Plumbing for Installing a Bathtub
The Art of Basic Plumbing for Installing a Bathtub
Blog Article
We have stumbled upon this article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround down the page on the internet and accepted it made sense to share it with you here.
Setting up a tub isn't specifically brain surgery, yet it does need solid plumbing, carpentry, as well as often, tiling skills. Changing an old bath tub with a brand-new one is likewise a moderately difficult job. If the old tub is conveniently easily accessible, the job can relocate rapidly; if you need to open a wall surface to eliminate the old bathtub as well as place the brand-new bath tub, the task is a lot harder. In either instance, the job is within a home handyman's abilities, although you will need an assistant to move out the old bathtub and set in the brand-new one. Ensure you have actually certified yourself for the task as well as are comfortable attempting it. As opposed to working with a specialist to take over a halfway-completed project, it is much better to take into consideration using one before you start. Opportunities are you might require a specialist plumber to make tube connections.
This short article will assist you install a new bathtub in your restroom if you have currently acquired a brand-new bathtub as well as don't require to transform the plan of your previous water supply pipelines.
Your devices as well as material list need to comprise the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, after that the first thing you should do is separate the supply of water. After doing so, activate the taps to drain pipes any water staying in the system. The procedure of removing the existing faucets can be quite troublesome due to the limited accessibility that is typically the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly come from the pipes. When the supply pipes have been removed, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this process. Once the taps have been eliminated, the holes in the bath/basin will have to be cleaned of any type of old sealing compound.
Before carrying on to fit the brand-new faucets, contrast the pipeline links on the old taps to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to avoid damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end offers a link to the current supply pipes.
If you require to fit a monobloc, then you will call for lowering couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the installing hole in the bath/basin ensuring that the washing machines remain in location in between the tap and also the sink. Protect the faucet in position with the producer offered backnut. When the faucet is safely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap ports. The previous type should be linked to the tap ends initially, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bathtub in the required placement. The wood boards are helpful in equally spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto four tiny factors.
The following objective is to make certain that the tub is leveled all round. This can be accomplished by inspecting the level and also changing the feet on the bathtub up until the spirit level reads level.
To set up taps, fit the bottom of the outermost versatile tap adapter to the suitable supply pipeline by making a compression join; after that do the very same for the other faucet.
Switch on the water as well as inspect all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as also check the overflow electrical outlet and also the normal electrical outlet for leakages.
Ultimately, fix the bath paneling as explained in the maker's instruction manual. Tiling and also securing around the tub must wait till the tub has actually been utilized at least when as this will certainly resolve it right into its final setting.
Planning for the Installment
To start with, the sustaining structure provided with the bath ought to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is very important to ensure that if the tap comes with a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets device to prevent pressure on the bathtub.
Fit the adaptable tap ports to the bottom of both taps making use of 2 nuts and olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you utilize every one of the supplied washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its last setting.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to break an inflexible seal, triggering the water to penetrate the wall in between the bath as well as the tiling, leading to difficulties with dampness and possible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components and installations. They are marketed in tubes as well as cartridges, as well as can sealing gaps as much as a size of 3mm (1/8 inch). If you have a larger void to load, you can load it with twists of soaked newspaper or soft rope. Keep in mind to always fill the bath tub with water prior to sealing, to enable the movement experienced when the tub remains in usage. The sealant can crack fairly very early if you do not think about this motion before securing.
Alternatively, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also quickly available on the marketplace. It is advisable to fit the ceramic tiles making use of waterproof or waterproof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm very serious about Installing A Bathtub and I'm hoping you enjoyed the new blog posting. Sharing is good. Helping others is fun. I value reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Emergency? Call us! Report this page